Audiotechnica Řemínek pro RPM 9, 9.2, 9.1, 10, 10.1

Bandje voor RPM 9, 9.2, 9.1, 10, 10.1

Pro-Ject

Accessoires voor platenspelers | Riemen en riemschijven

Original replacement strap for Project RPM 9 and RPM 10 turntables Square strap suitable for turntables: 1.2 x 1.2 mm / O 322 mm RPM 9 (9X, 9XP) RPM 9,1 RPM 9,1 X RPM 9.2 RPM 10 RPM 10,1 Evolution Note: If your turntable is not among the models listed, please refer to the configuration chart found in the download secti...

Meer ID: 275020 EAN: 8595122701505

Status

Nieuw

Beschikbaarheid

We hebben de nomenclatuur van de stapel veranderd. Artikelen met levering binnen een week zijn nu 'Op voorraad bij leverancier'. Artikelen met levering binnen twee weken zijn nu 'Op voorraad bij uitgever'.

Bij leverancier 2 st.

Verwacht op

Prijs

12,39 €

Prijs is inclusief BTW 21 %

Beschikbaarheid

Bij leverancier 2 st.

Verwacht op

Kerstlevering:

Artikelen die op voorraad zijn bij onze leverancier kunnen we voor Kerstmis leveren bij bestelling vóór 8. december. Na deze datum kunnen we de levering helaas niet garanderen.

Original replacement strap for Project RPM 9 and RPM 10 turntables

Square strap suitable for turntables:

1.2 x 1.2 mm / O 322 mm

RPM 9 (9X, 9XP)
RPM 9,1
RPM 9,1 X
RPM 9.2
RPM 10
RPM 10,1 Evolution

Note: If your turntable is not among the models listed, please refer to the configuration chart found in the download section for the appropriate strap.

All Pro-Ject drive belts are made from the highest quality materials and are optimized for specific model series of Pro-Ject turntables.

To extend the life of the drive belt, never touch it with your hands.When installing or manually changing the speed, use the special plastic wrench (supplied as a standard accessory with Pro-Ject turntables) and install the belt using the key on the pulley.

WHEN IS IT NECESSARY TO CHANGE THE STRAP?

Every turntable with a belt drive requires regular belt replacement. Exactly when this replacement is necessary depends on several circumstances such as environmental influences, frequency of use, etc.If you notice that the turntable is not reaching full speed, not maintaining the correct speed, fluctuating or cannot switch the rotation speed, it is time for the belt to reach its life limit.
To prevent these symptoms, a regular check of the belt is necessary. Remove the strap from the turntable and slightly tighten it. A good quality strap should not show any slight distortion of cohesion. If you see any cracks, it means that the strap has dried out over time and timely replacement is necessary.
If you do not use the turntable regularly and after a period of prolonged inactivity, the strap may stretch or break spontaneously.The straps dry out and age spontaneously and this process cannot be stopped. High temperatures and humidity have such a significant effect on the life of the straps. Regular strap replacement is thus a necessity and a guarantee of quality sound.
However, when replacing the strap, it is necessary to keep the original specification and most importantly - the same shape and dimensions of the strap.It is not possible to change from a square strap to a round or otherwise.A different shape would not be adapted to the pulley (motor drive axis) of the turntable and, as a result of the different contact area, the rotation of theThe rotation speed would not be correct and the friction could cause increased wear or breakage of the belt.